HyperLite F4 OSD V2 + Pyro32F3 45A

$5,907.93 $6,564.83

1 x HyperLite F4 OSD V2 With VTX Pit Mode

En stock

1 x Pyro32F3-45Amp 4in1 F3 32bit BLHeli ESC 4x45A

En stock

Version 2.3 Update:
Attention! you have to update your FW 3.5.5 or up for the VTX pit mode.
The Pyrodrone F4 OSD has a new feature!
VTX Pit mode compatibilty.

Now there are sellector pads for your VTX voltage input!
5V and VBAT.
First please jump the correct side pads according to the VTX you are using.

And then jump the two pads on the “PIT” side ( If this feature is not needed then just jump the pads of the “ON” side and your VTX will always be on)
After you jump the PIT pads connect to Betaflight and go to CLI page , type in the following commands:

resource PINIO 1 A15
set pinio_box = 39,0,0,0
type “save” and then hit enter.

Wait for the FC to reboot, then go to the “MODES” tab in Betaflight and set VTX PIT MODE to an AUX channel you prefer

Done! 🙂

Check the below Race footage from MewoFPV Cory Ibanez 1st place winner at the Nytfury VS Dolma Callout Race using the PyroDrone F4 OSD Flight Controller.

Straight gold. The US currency should be backed by this FC! (Cory Ibanez)
If you have V2.2 or V2.3 Boards please adjust the voltage scale in the Betaflight Power and Battery page as follows:
82 > V2.2
161 > V2.3

HyperLite F4 OSD

One of the most popular FC is back and better than ever, combining an industry favorite layout with new feature sets for freestyle, long range, and racers. Finally, a board for every pilot!
The new Hyperlite F4 OSD takes the same celebrated flat-bottomed layout (crucial for clean and tight builds) and adds a much appreciated OSD and SIX UART ports (more than any other board on the market!) for GPS, RX, SmartAudio, and even Camera Control.
And with more features, comes improved ease of use with a built in 4-in-1 ESC socket and included harnesses for HobbyWing 45Amp G2 ,AiKON AK32, and Spedix GS35 4in1 ESCs. The built in solder pads mirror the 4in1 pad layout, so you can easily connect ANY ESC to this board to get features like current sensing and ESC telemetry (for the BL32 guys).
PLEASE NOTE: The Hyperlite F4 OSD uses its own BF target .bin, PYRODRONEF4.
Tech Specifications:
MPU6000 Gyro
STM32F405 CPUE @ 168mhz, can be overclocked
2-6S direct battery input
3.3V 100ma, 5V 1.2A BEC
5V Camera Power
Built in configurable Betaflight OSD
Flat bottom PCB for SUPER CLEAN builds
36×36 PCB with 30.5×30.5 mounting holes
          UART2 (FREE),
                  UART3 (INVERTED TELEMETRY), use CLI command : Set tlm_halfduplex=off
                  UART4 (Free),
                  UART5 (Smart Audio)
                  UART6 (Free)
Built in 4 IN 1 ESC socket(including ESC telemetry, External current sensor)
Plug and plug with the most popular 4-in-1 ESCs (HobbyWing, Airbot, Spedix, Aikon),with supplied cables
Built in solder pads mirror of the 4-in-1 ESC socket
Printed layout instructions ON the board – no need for instructions!

Based on 0 reviews

0.0 overall

Be the first to review “HyperLite F4 OSD V2 + Pyro32F3 45A”

There are no reviews yet.